associatesfere.blogg.se

2016 ford edge front license plate bracket

#2016 ford edge front license plate bracket how to#
#2016 ford edge front license plate bracket trial#
#2016 ford edge front license plate bracket license#
#2016 ford edge front license plate bracket series#

Press the bracket upwards against the bumper and hold it firmly in place for about 30 seconds to ensure good adhesion.

#2016 ford edge front license plate bracket license#

Remove the backing on the double sided tape on the horizontal section of each bracket, and carefully align the license plate and bracket assembly once again on the front of your bumper.These sections should be completely clean and dry to ensure that the double-sided tape on the bracket will adhere well. Alcohol is a good cleaning fluid to use, but soap and water will also work. Carefully clean the sections on the underside of the bumper you noted in the above step.Then note the location where the two horizontal bracket sections contact the underside of the bumper.

You may need to slightly loosen the angle adjustment screws. Angle the plate to the desired angle with respect to the bumper by adjusting the angle of the left and right brackets. Be sure to center the license plate with your grill.

Position the license plate assembly in the desired location on your front bumper.

Don’t tighten the screws too tightly at this point. Do the same for the left bracket with the other 2 screws and washers.

With the hex key, attach the right bracket to the right rear side of your license plate, using 2 of the 4 included cap screws and 2 of the 4 included stainless steel trim washers.

Tighten each front screw, while ensuring that the horizontal brackets are perpendicular with the slot in the vertical section. Slide the horizontal section of each bracket so it is this distance from the top end of the vertical brackets. Using the included hex key, loosen the front stainless steel button-head cap screw on the left and right brackets.

First, measure the distance from the lower edge of your bumper to where you want the top of your license plate to be.

Installation is extremely easy, and takes about 10 minutes.

Our low profile front license plate bracket comes pre-assembled in two parts – a left side and a right side, as illustrated in the sketches above.

These step-by-step instructions are included with the bracket.

#2016 ford edge front license plate bracket series#

This series of photos will guide you through each step of the simple installation process.

#2016 ford edge front license plate bracket how to#

Video: How to install the Skene Design license plate bracket Step-by-Step Instructions Not sure if you want to install your bracket yourself? Many of our customers prefer to have the bracket installed by an automotive professional: any mechanic or body shop can do it. You’ll provide your own drill and Phillips screwdriver. The bracket comes with an installation kit that includes: a drill bit, all the mounting hardware, and a comprehensive installation guide. It’s easy to install the Skene Design license plate bracket. To be clear, this is not a discussion on how to get around not having a front plate or the legality/loopholes surrounding it, this is a request for a guide on how to install the front license plate bracket. As much as we all love a naked front on our RS's (hubba, hubba!), there comes a time that we in California must mount our front license plates. Most jurisdictions require a front and back license plate but it is safer to check first to avoid incurring a violation. Before installing a holder for a front license plate, check with the Department of Motor Vehicles office locally if you are required to have a front license plate in the state you are in. Howard in parts shows customer how to install license plate bracket he purchased for his brand new car.

#2016 ford edge front license plate bracket trial#

2) Trial fit the license plate bracket to the vehicle to verify fit.

Vehicle plates and are not used in this installation. This is where the license plate bracket mounts. They are located near the center of the vehicle. Then put the 1/4 inch rivets in and you should be all set.ġ) Find the 2 dimples on the front bumper. Then take a 1/4 inch bit an drill them out. Those are easy, but thats prolly because i work for ford but, just center it on the front bumper and make a mark where the two hole are.